The Reaper V3 is a renowned rebuildable tank atomizer by EVL Vapors, featuring excellent build quality, and very short 33mm height design, and top notch flavour performance.
Choose from two versions:
Or if you can't decide, get one version, and get the opposing air flow kit so that you can configure your Reaper V3 for either method as you desire!
All EVL Vapors Reaper V3 products come securely packed in a metal tin and packed with Muji cotton for your wicking pleasure! Practical on two ends!
One of the newest upgrades to the Reaper V3, is the "HexAirgon Ring", a new style of airflow ring which has allowed o-rings and any other extraneous mechanism to be removed to secure the ring. Instead, you simply choose which of the 6 airflow settings you desire, place the ring on the mod, and screw the atomizer down. The mod combined with the internal hexagonal profile of the ring securely holds the ring in place and the internal hexagonal profile stops it from revolving.
Air flow options on the standard (DL) HexAirgon Ring are 1mm, 1.2mm, 1.5mm, 2.0mm, 2.5mm, and 2.7mm to deliver a nice restricted direct lung hit through the 2.7 air port on the deck.
The MTL version has different air flow options, with the following air flow sizes for the MTL HexAirgon Ring: 0.8mm, 1.0mm, 1.2mm, 1.4mm, 1.6mm, and 1.8mm through the 1.8mm air port on the MTL deck.
Users can purchase either of the decks to fully complement the version of the atomizer they choose, and easily change out the decks by simply unscrewing the positive 510 screw on the bottom of the atomizer and pulling the deck directly up and out. Push the replacement deck back into the well, refit the 510 screw, and you are good to go!
For MTL users looking for a more refined MTL experience, there are dedicated restricted airflow MTL decks with tighter 1.0mm or 1.2mm air outlets for a tighter air flow under the coil:
For users looking to use the Reaper V3 with a 24mm outer diameter beauty ring to beautifully merge their atomizer to their mod, the optional 22<24mm HexAirgon Ring will do the trick, integrating beauty ring sizing with air flow functions for unimpeded air flow performance. This larger air flow ring can be purchased >>HERE<<.
Gone is the top fill, and back to the V1 style bottom filling. This method was chosen as it is simple and can be filled via a much wider range of methods and automatically resets the vacuum in the atomizer with each refill.
Capacity on the standard tank is 2mL, but different tanks of different sizes, capacities, and materials can be purchased at these following links:
The tank as it comes with this version of the Reaper V3, has a capacity of 2mL and is made of Ultem for maximum liquid attack resistance, durability, and light weight while maintaining the ability to see your liquid levels throughout the entire tank. Optional tanks are available in clear polycarbonate or full metal stainless steel tank option for maximum durability.
The chimney is a wonderfully simple one-piece design using a Nitrile o-ring at the top which securely holds the tank in place and a silicone o-ring on the bottom so that the tank can be easily unscrewed.
A redesign here has seen the juice ports resized and juice supply volume nearly doubled, allowing for higher wattage vaping. Also, the juice ports are located on the very bottom of the tank, allowing users to vape the tank until it is completely empty. As such, the capacity of the tank is the actual capacity you can vape! No more leaving a mL of liquid at the bottom of the tank because they can't reach raised wicks!
Gone are the threads which connect the chamber cap to the base section. Instead, a new nub system allows the cap to be popped on and off with a simple twist and push/pull. This feature also allows the chamber cap to move in two directions:
To remove or refit the tank, simply line up the "V" in the "EVL" engraving with the little cut out on the base section, push on, or pull off, and twist to the desired position.
In essence, if the "V" from the EVL engraving is over the air intake hole, then you are ready to vape. If it is sitting somewhere in-between any of the holes on the airflow ring, then the tank is closed off.
The white PEEK ring that surrounds the deck can be turned, allowing users to adjust the juice flow being supplied to the wicks. This adjustment should allow the use of high wicking materials or simply to fine tune your build.
NOTE: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Vapes by Enushi is not responsible for misuse of product, or dangerously low coil builds. Vapes by Enushi is not liable for the use of improper batteries for your builds.
Showing reviews 1-3 of 5 | Next
Posted by Jason Y on 2019 Jan 28th
This RTA is easy to wick The Flavour is better than some RDAs I would recommend this as a must buy. I wish I would have bought the larger tank because they are out of stock now. Its a must buy. Service is great and shipping is super fast 4 days to my home in Tokyo.
THX Brian and Staff
Posted by CLARK E GARDNER on 2019 Jan 9th
Great flavor..endless air flow options and superb build quality..this rta is very easy to build on and rewick..filling it does require removing the tank but so does alot of other rtas so I was no big deal to me..nice little flavor rta for the money
Posted by Catherine on 2019 Jan 5th
Wonderful atties very smooth and easy to build and the flavour is top notch very pleased with it
Showing reviews 1-3 of 5 | Next
All prices are in CAD