The Tripod is Atmizone's new approach to 22mm RTA design for single coil setups. It offers an unparalleled vaping experience focusing on performance, versatility and ergonomics.
Check out this fantastic >> Review of the Tripod RTA by The Vape Review <<!
You may browse our entire list of Tripod RTA related items >> HERE <<.
With its enhanced flavour and vapour production, potential for variable specs, instant real time access to deck, instant top refill system, easy rebuilding and attention to details, the Tripod is one step ahead of most RTA's on the market.
Available in either SS Matte (a classic machine-brushed finish), or SS Ice Matte (a media/bead-blasted finish).
The deck of the Tripod is targeted for single coil setups with design details aiming to facilitate and improve rebuilding process as much as possible. Focusing on some of them, you can see high precision large pan head phillips post screws, conveniently placed rails to capture wire either between rail and screw head / body or around screw body (depending on wire gauge), cut-outs on outer deck rim for easier rebuilding, cut-outs on inner deck rim plus cotton wells to help proper cotton placement and liquid distribution along cotton body, sufficient liquid intake slots on deck sides (approximately 4.0mm x 2.0mm). The Tripod deck can literally host any size of single coil build, from classic small sized coils up to large complex/exotic coils.
You may tune air flow via four MTL pin options (1.0mm, 1.2mm, 1.5mm, or 1.8mm) pinned inside a 4.0mm diameter nest. You may also regulate more "airy" flow via the external Air Flow Control System (AFCS) Ring located at the base of the atomizer, adjusting from zero to 4.0mm full open air diameter.
With the Tripod, we introduce the Chamber and Chimney (C&C) Reducer assembly. It consists of two parts that sandwich the upper part of the Chimney. When assembled, the C&C Reducer forms a vaporization chamber with lower volume (approximately 5.3mm chamber height) and a chimney with 3.0mm inner diameter, focusing on flavour oriented setups rather than vapour production. When removed, the chamber offers approximately 9.0mm coil height space and the chimney gets approximately 5.3mm inner diameter, with proper geometry to get all the clouds you want. The C&C Reducer actually offers you the potential of two different chamber and chimney geometries, thus two different single coil RTAs.
The custom drip tip that comes with the device is a two-part assembly as well, with its two parts sandwiching the Top Cap to ensure extra stability when removing top cap to refill. The drip tip is easily removable to let you use your own 510 drip tip.
The standard liquid capacity of the Tripod RTA is 2.0 mL, but can be extended with the >> Tripod 3.4 mL Extension Kit <<, which increases the overall height of the Tripod by only 6mm!
Atmizoo has based the design of the Tripod on the concept of a threadless mechanism with twist and pull / push actions in order to design and manufacture high precision parts that make vaping with an RTA so much easier. Instant access to deck can't get any simpler and quicker. You just twist, align the small triangles that are located on the sides of the chimney and deck and then pull in order to access your deck very quickly, any time, even with a full tank of liquid. A similar concept is applied to the top cap for refilling liquid, simply align triangles on the side of the top cap with the dot on the rim on the tank and pull up to refill through the large liquid slots. No need to worry if the dots and triangles are difficult to see, you can twist while pulling gently until you feel with the tabs locate to the notches as the unlocking point of each mechanism.
Before using Tripod for the first time, it is strongly recommended that you take a good look at the >> Atmizoo Tripod Support Section <<, with tons of useful information about the Tripod, including detailed introduction, assembly/disassembly guides, useful tips, etc.
The Lab comes with a fair and generous >> warranty <<, which covers all manufacturing defects.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Vapes by Enushi is not responsible for misuse of product, or dangerously low coil builds. Vapes by Enushi is not liable for the use of improper batteries for your builds.
Showing reviews 1-3 of 11 | Next
Posted by AD on 2020 Nov 27th
The top cap is too tight and extremely hard to remove for refilling. The air inlet can't be turned without turning the chimney. Taking the device apart requires a magnifying glass to match up arrows, a tiny dot and the whole device is a twisting, turning Rube Goldberg machine.
Posted by Daniel H. on 2020 Aug 26th
My first High end RTA, the precision is beyond compare!!
The ability to dial the vape you want down is amazing for MTL, recommend to buy the extra Positive adapters for an even better dialled vape. But the 2Ml capacity is the only downside!!
Flavour is amazing!! But you’re juice might need some more dialling with this RTA.
Posted by Marco on 2020 Mar 28th
Fantastic. Can’t say enough about this one. I love it. Hits hard, awesome flavour. Only downside is 2ml capacity but because it’s a single coil, not sure it’s actually a bad thing.
If I lost it today, I would order another right away (if there were any available).
Showing reviews 1-3 of 11 | Next
All prices are in CAD