Loading... Please wait...

Categories

Armor Mods - "Armor 2.0" RDA

Hover over image to zoom

  • Armor Mods - "Armor 2.0" RDA
  • Armor Mods - "Armor 2.0" RDA
  • Armor Mods - "Armor 2.0" RDA
  • Armor Mods - "Armor 2.0" RDA
  • Armor Mods - "Armor 2.0" RDA
Armor Mods
USD$124.49
Weight:
0.04 KGS
Maximum Purchase:
1 unit(s)

Sorry but this item is currently unavailable. Please check back at a later stage.

 Product Description

Armor 2.0 RDA by Armor Mods

The Armor 2.0 RDA by Armor Mods takes everything that the original 1.0 Armor RDA was good at, then improves it further, with a reinforced post design to prevent bending, deeper juice reservoir, more internal space to fit coils up to 3.0mm in diameter, and a redesigned air flow system.

Official launch date: 21:00 EST (9pm) on Friday, May 11th, 2018. >>CLICK HERE FOR COUNTDOWN TIMER<<

The redesigned air flow control system now allows users to completely close off one side of air for single coil usage in combination with the included single coil reducer (SCR), or to open it fully to allow air to hit both coils in dual coil mode. A redesigned cap and air flow control ring and lock system allows users to adjust the air inlet aperture to their desired size, and the AFC lock ring (compatible with Armor 1.0 RDA) will secure the AFC ring in place.

A single coil reducer (SCR) is included to effectively block off half the chamber space and air flow from that size to maximize flavour production. Made from PEEK, it is very resilient to heat.

Proprietary sized black Delrin drip tip is included to minimize heat transfer to the user's lips.

Deeper juice well allows greater juice capacity.

Re-engineered two-post build design allows for a much more solid post design, resolving issues where users were over-tightening and causing posts to bend or twist.

LIMIT ONE PER PERSON

Restricted zone item: This item cannot be shipped to any countries in Asia or Europe. Any orders for this product in to these regions will be cancelled and refunded.

Incredible flavour and vapour is produced with this single or dual coil atomizer with an ultra compact chamber.

22mm outer diameter.

Package Contents:

  • Armor 2.0 RDA
  • Bottom feed pin (already installed)
  • Solid pin for standard dripping
  • Black Delrin proprietary sized drip tip
  • Spare o-rings
  • Spare coil post grub screws

WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.

DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.

Vapes by Enushi is not responsible for misuse of product, or dangerously low coil builds. Vapes by Enushi is not liable for the use of improper batteries for your builds.

 Find Similar Products by Tag

armor  armour  Atomizer  BF  Bottom  Dripping  Feed  Mods  RDA  Rebuildable  

 Find Similar Products by Category

Vendors Other Products

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...

newsletter

Follow us on

Copyright 2018 Vapes by Enushi. All Rights Reserved.
Sitemap | Bigcommerce Premium Themes by PSDCenter

Click the button below to add the Armor Mods - "Armor 2.0" RDA to your wish list.