Loading... Please wait...

Categories

Hussar Vapes - "Hussar Legacy" BF-Ready Rebuildable Dripping Atomizer

Hover over image to zoom

  • Hussar Vapes - "Hussar Legacy" BF-Ready Rebuildable Dripping Atomizer
  • Hussar Vapes - "Hussar Legacy" BF-Ready Rebuildable Dripping Atomizer
  • Hussar Vapes - "Hussar Legacy" BF-Ready Rebuildable Dripping Atomizer
  • Hussar Vapes - "Hussar Legacy" BF-Ready Rebuildable Dripping Atomizer custom fabricated coil screws
Hussar Vapes
USD$160.66
Weight:
0.09 KGS

Sorry but this item is currently unavailable. Please check back at a later stage.

 Product Description

The "Legacy" by Hussar Vapes

The Legacy by Hussar Vapes is an atomizer that Hussar Vapes is a bottom feed ready rebuildable dripping atomizer designed to suit vapers who use fruitier/fresher e-liquids while maintaining a lot of custard profile.

Airflow has been increased compared to the Hussar RDA 1.0, where the Legacy has two 7.14 mm2 air intake slots, totaling 14.28 mm2 in comparison to the Hussar RDA 1.0 which had two 4.6 mm2 air intakes for a total of 9.32 mm2 .

Building on the Legacy is easy and flexible, thanks to the 4-screw system that allows thoughtless single coils builds. This aids in not having to think about which way to wind the coil legs, either clockwise or counter-clockwise will work!

Screws have been specially designed and custom machined for the Legacy. In order to deliver a much more pleasant building experience, Hussar Vapes tested many different solutions and materials, deciding on a 1.8mm wide flat surface beneath the head of the screw to allow builders to easily use any wire desired without a need to bend it. Stainless steel is used for these screws in order to ensure longevity and reliability.

The Legacy is using a feeding system as seen before on the Hussar RDA 1.0 but improved; when the squonk bottle is pushed, the liquid is released from the sides of the pin location to saturate the cotton wick on both ends. Juice wells have also been widened in the deck of the Legacy to ensure more vaping time between each squonk. Excess liquid gets drained back through the pin, and approximately 1 to 1.5 mL of liquid is left in the atomizer deck (depending on how much cotton is placed in the well. A user can enjoy as much as 20 hits before the need to squonk again. This large well system also makes the Legacy much more difficult to over-squonk.

A solid non-BF pin is also included in the set for standard dripping usage.

This release has newer improved o-rings to solve the issue about users complaining about previous o-rings being so tight that the cap was difficult to remove.

Specifications:

  • 316 stainless steel construcction
  • 2x Black NBR70 15x1 o-rings
  • 1x Black NBR70 3x1 o-ring
  • 4x Custom machined stainless steel flat post screws
  • Handfinished for round, smooth edges
  • Hand finished satin deck
  • BF pin for side feeding system
  • Stainless steel low profile wide bore 510 drip tip included
  • Gold plated positive post for best conductivity and minimal oxidation.

Spare Parts:

  • 2x Black NBR70 15x1 o-rings
  • 1x Red silicone 15x1 o-ring
  • 1x Black NBR70 3x1 o-ring
  • 2x Custom machined stainless steel flat screws
  • Solid NON bottom feed pin

Packaging:

  • Custom made wooden box/510 stand by Custom Wood

NOTE: This product cannot be sold to Asia. If the intended destination of your purchase of this item is going to Asia, then your order for this item will be cancelled and refunded to you.

WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.

DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.

Vapes by Enushi is not responsible for misuse of product, or dangerously low coil builds. Vapes by Enushi is not liable for the use of improper batteries for your builds.

 Find Similar Products by Tag

BF  Bottom  Feed  Hussar  legacy  RDA  squonk  Vapes  

 Find Similar Products by Category

Vendors Other Products

 Product Reviews

  1. Pretty Little Thing

    Posted by LARRY MILLER on 2018 Dec 11th

    This is the first Hussar Vapes product I have owned. Purchased because so many in the vape world rave about them.

    Machining is exquisite; no sharp edges, no swarf, tight tolerances, etc. Popping in a coil is basically mindless it is so simple. Top cap is a little snug, but loosens once the interior gets a little juicy. And, it looks terrific.

    Big airflow for a small device. I like to have available more air flow than I need, and this delivers. Air slots are vertical ovals which makes little sense for a deck designed for a horizontal coil. Still puzzled over that. You may have to fiddle with coil height to find what works best for you.

    Flavor is very good. Note that this atomizer presents components of favorite e-liquids differently than several of my other atomizers. This is not necessarily bad, but you might find your favorite liquid may not taste the same in the Legacy.

    Air flow is smooth with little to no whistle that is common in single-coil, dual air flow devices (i.e. I hate whistling!). It does produce a whoosing noise on intake that is different than other atomizers I use. Do not think it is noisier, but the pitch of the air intake is unique.

    With the BF pin, the squonk action is unique and very slow. It will take a short period of time to regulate how hard you push on the squonk bottle to provide adequate liquid to the wick ends. I often will press my bottle firmly for 3-5 seconds to attain decent saturation.

    Overall, the Legacy is a very good atomizer. It can accommodate fairly large coils, if that is your thing. It tends toward being a cloudy atomizer over a strictly flavor-type atomizer. It does not, however, trump other BF atomizers I currently use. If you wanted to enter the high-end RDA space, the Legacy might be an atomizer you should consider. If you are pretty well set with good RDAs, this one will not raise the bar.


  2. High airflow in a compact dripper.

    Posted by Mitchell Wayne on 2018 Dec 10th

    Crazy airflow for the size of the BF atty. heat displacement is good enough to fit massive wraps around a 3.5 id. Use ultem tips to have the smoothest/ most comfortable hit. all around great little atty.


You Recently Viewed...

newsletter

Follow us on

Copyright 2019 Vapes by Enushi. All Rights Reserved.
Sitemap | Bigcommerce Premium Themes by PSDCenter

Click the button below to add the Hussar Vapes - "Hussar Legacy" BF-Ready Rebuildable Dripping Atomizer to your wish list.